Filter By:
- Bar Ends (18)
- BMX (108)
- Bottom Brackets (135)
- Brakes/Levers/Pads (533)
- Cables (207)
- Cassettes/Freewheels (96)
- Chainrings (174)
- Chains (108)
- Show More Categories
- Cranksets (282)
- Derailleurs (199)
- Forks (139)
- Groups (2)
- Handlebar Grips/Tape (377)
- Handlebars (319)
- Headsets (168)
- Pedals (291)
- Recumbent (1)
- Saddles/Pads (387)
- Seatposts (121)
- Shift/Brake Combinations (67)
- Shifters (111)
- Shocks (31)
- Stems (182)
- Other (853)
- Show Fewer Categories
- Show More Brands
- Show Fewer Brands
- Show More Prices
- Show Fewer Prices
- Show More Sizes
- Show Fewer Sizes
Parts
$0.35
Hope Pad Clip
• Fits Tech and Tech Evo M4, X2, and V2 Brakes
$0.79
Sunlite's Cable End Button replaces the worn out piece that goes between your brake cable and the brake lever body. Replacing it along with cables and housing helps add new life to your brakes and shines u the bike, too!
$0.84
RaceFace X-Type Bottom Bracket Outer Race Seal
- Replacement for cracked or broken X-Type outer race seals
- Sold each
$1.00
• Specially-formulated plastic liner prevents brittleness
• SLR/M housing compatible
• Plastic
$1.00
• Custom colors used on project one bikes
• Specially-formulated plastic inner line prevents brittleness
• SLR/M housing compatible
• Plastic
$1.00
Interlok spacers nest into the lip of Cane Creek headset uppers for a rock solid, flex-free fit.
- Composite construction
$1.00 - $52.50
- Prime 2-piece rotors are for Prime Pro and Expert brakes only
- L-series, lightweight one piece rotors
- V-cut profile steel rotors for optimum weight-to-performance ratio. Increased surface area over previous designs increases power while cutouts and drillings help keep pads clean
- Rotors includes: (1) 6-bolt/44mmBCD rotor, (1) Torx wrench, and (6) T-25 rotor mounting bolts with thread retaining compound
- 205g @ 203mm
$1.00
Jagwire's Tube Tops are installed over your cable housing sections to provide a soft bumper to deaden the impact of cables hitting your frame while riding, minimizing rattles and protecting your frame's fine finish. They feature a split seam so they're easy to install by hand with no cable disassembly required. Just open the Tube Top's seam, put it on the housing where it's rubbing the frame, rotate the seam so it faces out and release. The Tube Top will stay in place and keep your bike quiet and safe.
$1.00 - $12.00
- Hoods with (FD) are Flight-Deck compatible
$1.00
- 50 feet (15.2 meters) length
- 5mm diameter cable housing
- For brake cables
$1.00 - $24.72
• 50 feet (15.2 meters) length
• 5mm diameter brake cable housing
$1.08
Shim spacers can be placed between bearing and compression cover in IS headsets to fine tune the fitment.
$1.50
KMC 3/16" Master Link Chain Links
- For 3/16" chain, extra wide
- Extra-wide, for non-derailleur bikes: BMX, cruisers, etc
- Perfectly fits on KMC 415H & 415H-NP chains
$1.50 - $2.00
- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension
- Uses standard chain pin connector and tool
$1.59
- Model: Derailleur Bolt & Nut
- Compatibility: Mounts rear bracket to frame
$1.79
- Routes cables underneath the bottom bracket
- Will not rust or corrode
$1.80
- HFX-9 kit includes a pre-crimped inline caliper fitting
- Sole and Stroker Ryde kit includes specific fittings for lever and caliper
Page 1 of 159
Next page